Bed side table with drawers

Start with the count: 18 bedside tables with drawers

We stock 18 bedside tables that include at least one drawer. That is the full set this guide draws on, and every number below comes from that group. The range runs from $37.91 to $188.36, so there is a clear entry point and a clear top end. Before you compare finishes or handles, measure the gap between your bed and the wall, and note the height of your mattress top. A bedside table that sits more than a few centimetres above or below the mattress line feels wrong every time you reach for it. The 18 products here vary in width, depth and height, so the tape measure matters more than the photograph. Write your three measurements down before you open a product page.

What is actually in stock right now

Of the 18 bedside tables with drawers, 6 are wood, 2 are rattan, 1 is fabric and 1 is metal. The remaining 8 are not assigned a material in our listing data, so treat the material field as incomplete rather than as a full breakdown. On features, 15 have a drawer, 9 have a shelf and 7 are described as offering storage. Those counts overlap: a table with a drawer and a shelf is counted in both. Drawer count is clearer: 7 tables have 2 drawers, 1 has 3 drawers and 1 has 4 drawers. The rest are single-drawer or unspecified. Prices across the 18 run from $37.91 to $188.36. If you need two matching tables, check stock on both before you commit.

Match the drawer count to what you actually store

One drawer suits a book, a charger and a pair of glasses. Two drawers let you separate the things you touch daily from the things you touch weekly. Three or four drawers start to replace a small chest, which is useful in a rented room where you cannot add furniture. In this range, 7 tables have 2 drawers, 1 has 3 drawers and 1 has 4 drawers. The rest are single-drawer or not specified. Be honest about volume: a drawer 10 cm deep holds less than it looks like it will. If you keep a tablet, a notebook and a water glass on top, the top surface area matters as much as the drawer count. Measure the footprint of what you plan to put on top before you choose.

Check the height against your mattress

A bedside table works when its top sits close to the height of your mattress. Too low and you reach down in the dark; too high and you knock things over. Measure from the floor to the top of your mattress, then compare that with the listed height of the table. Only 2 of the 18 products list a dimension value in our data, and the only figure present is 15.8 inches. That is a single measurement attached to a single product, not a typical height for the range. For the other 16, you will need to open the product page and read the dimensions there. Do not assume a table is the right height because it looks right next to a bed in a photograph.

Choose a material for the room, not the trend

Wood, rattan, fabric and metal all appear in this range, and each behaves differently in a bedroom. Wood is the most common material here, with 6 of the 18 tables. Rattan appears on 2, fabric on 1 and metal on 1. The remaining 8 are not assigned a material in our listing data. Wood suits a solid, quiet look and is easy to wipe. Rattan adds texture and suits a lighter room, but the weave can catch on knitwear. Fabric softens a room and hides small marks, though it collects dust. Metal is slim and cool, and often works where space is tight. None of these is better in the abstract. Pick the one that matches the light and the other surfaces in the room.

Plan the floor space before you buy

A bedside table needs clearance on three sides: the wall behind it, the bed beside it and the floor in front. If the gap between bed and wall is under 40 cm, a narrow table is the practical choice. Several products in this range are described as narrow or slim, which usually means a reduced depth rather than a reduced height. Check both figures. Also check the door swing if the table sits near a wardrobe or room door. A table that fits the gap but blocks a drawer opening is not a fit. Leave enough room to pull the drawer out fully; a drawer that opens halfway is a shelf with extra steps. Measure the gap, then measure the drawer travel.

What this guide cannot tell you

Two products can be described in the same words and still differ. Drawer runners, joinery, finish and assembly can all vary between items that share a material and a drawer count. Our listing data does not capture those details, and we have not tested the products. Where a dimension is missing, we have said so rather than estimate it. Where a material is unassigned, we have counted it as unassigned rather than guess. The individual product page is the governing description for any specific table. Use this guide to narrow the field, then read the product page for the item you are about to buy. If the page and this guide disagree, the page wins.

Set a budget and stick to it

The 18 tables here run from $37.91 to $188.36. That is a wide band, and the difference is not always visible in a photograph. Decide what you need the table to do before you decide what to spend. A single drawer and a flat top may be enough, and that sits at the lower end. Multiple drawers, a shelf and a specific finish push towards the upper end. Delivery and assembly can add cost and time, so check both before you order. If you are buying two tables for a double room, the pair may cross a budget line that a single table would not. Set the number first, then filter the 18 by price, then by drawer count.